CCP1-1T CCP1-2T
规格
额定量程 490.3 N {50 kgf}～196.1 kN{20 tf}
安全过载 150 %R.C. (CCP1-50K～100K：500 %R.C.)
极限过载 200 %R.C. (CCP1-50K～100K：500 %R.C.)
额定输出 3 mV/V±0.003 mV/V
非线性 0.05 %R.O.
滞后性 0.02 %R.O.(CCP1-50K～100K：0.05 %R.O.)
重复性 0.02 %R.O..(CCP1-50K～100K：0.05 %R.O.)
推荐激励电压 12 V 以下
最大激励电压 20 V
零点平衡 ±0.03 mV/V
输入电阻 350 Ω±3.5 Ω
输出电阻 350 Ω±5 Ω
绝缘电阻 5 000 MΩ 以上(DC50 V)（电桥～主体之间）
补偿温度范围 －10 ℃～70 ℃
安全温度范围 －20 ℃～100 ℃
温度变化对零点的影响 0.03 %R.O./10 ℃
温度变化对输出的影响 0.03 %LOAD/10 ℃
电缆 φ10、带4芯屏蔽线3 m直接连接、带前端Y型压接端子
防护等级 IP64
弹性体的材质 合金钢
涂装 环氧树脂涂装（Munsell 6GY3.5/2半光泽近似色）
寿命 额定量程时1 000 000次
CCP1-1T CCP1-2T
供应日本NTS称重传感器
AST5300差压传感器
The AST5300 wet/wet differential pressure transducer offers a maximum line pressure of 1,500 PSI. The AST5300 has no oil filled cavities or O-rings, eliminating risk of contamination and maximizing safety. Available in 4-20mA or voltage outputs, this differential pressure transducer can offer a cost effective alternative for flow, level and filtration systems in industrial, semiconductor, or oil and gas applications. The AST5300 can be configured as an explsion-proof or non-incendive differential pressure transducer for applications including natural gas filters and well head valve monitoring, and process flow measurement.
Design Benefits - High Line to Low DP
- Class I & II Div 1 Explosion Proof (AST53ED)
- Class I Div 2 Non Incendive (AST53EN)
- Oil Free - No Containment Issues
- Wide Operating Temperature
- Compatible With Various Liquids and Gases
- Compact size
- Differential pressures between 1 and 10 PSID available
Applications / Industries Flow measurement of Liquids / Gases
- Tank Level Monitoring
- Ballast Measurement
- Filtration
- Cryogenics
AST5400湿/湿差分压传感器
AST5400 wet/wet differential pressure transducerscan measure the differential pressure of liquids or gases with line pressures up to 5,000 PSI (350 bar) and a turn-down ratio of 15 to 1. Using Krystal Bond Technology, the AST5400 differential pressure transducer contains no silicone oil, O-rings, or welds. The low strain level on the diaphragm results in accurate, repeatable measurements.
The AST5400 wet/wet differential pressure transducer is commonly used to measure differential pressure across filters or calculate flow across an orifice plates. With its digital compensation, the AST5400 DP offers excellent linearity and performance over temperature.
The electronics offer a fail safe condition on the output signal.
The AST5400 DP can be manufactured using 316L, 17-4 PH, Inconel 718, or Hastelloy C276 and is available for hazardous locations.
Design Benefits - Krystal Bond? Technology
- ABS Type Approved
- Class I Division I&II ratings
- ATEX Exd IIC flame proof / ExnA IIC available
- Both or either pressure port can see full line pressureNo expensive 5-way equalization valves required!
- Bi-directional measurement available
- Smart electronics with failure condition protection
- Wide variety of materials for corrosive liquids and gases
- Contact AST about additional line pressure or temperature outputs for OEM applications
Applications / Industries Aerospace Controls
- Analytical Instruments
- Fuel Systems
- Filtration
- Hydraulics
- Hydrogen (316L only)
- Upstream pressure monitoring
- Compressor controls
- Exhaust / Vapor monitoring (contact AST for low pressures)
- Marine Instrumentation
- Desalination Equipment (Inconel718 Recommended)
- Water Makers
CCP1-1T CCP1-2T