绿电直流12V10A120W监控集中供电电源LED稳压开关电源工业电源

型 号MODEL

LD-12120

LD-24120

输出OUTPUT

直流电压DC VOLTAGE

12V

24V

额定电流RATED CURRENT

10A

5A

电流范围CURRENT RANGE

0-10A

0-5A

额定功率RATED PWER

120W

120W

纹波与噪声最大RIPPLE AND NOISE

120MV VPP

200MV VPP

电压调整范围VOLTAGE ADJ RANGE

10.8-13.2V

21.6-26.4V

电压精度VOLTAGE TOLERANCE

±2﹪

±2﹪

线性调整率 LINE REGULATION

±0.5﹪

±0.5﹪

负载调整率 LOAD REGULATION

±0.5﹪

±0.5﹪

启动.上升时间 SETUP RISE TIME

500MS.30MS/230VAC 1200MS.30MS/115VAC满载

保持时间 HOLD UP TIME（TYP）

20MS/230VAC 10MS/115VAC满载时

输入INPUT

电压范围 VOLTAGE RANGE

180V-264V

频率范围 FREQUENCY RANGE

47-63HZ

效率 EFFICIENCY

82%

84%

交流电流 AC CURRENT

2.5A/115VAC 1.5A/230VAC

浪涌电流 INRUSH CURRENT

45A冷启动Cold boot

漏电流 LEAKAGE CURRENT

＜2.5MA/240VAC

保护PROTECTION

过负载 OVERLOAD

额定输出功率的110%-150% Rated output power

短路 OVER VOLTAGE

保护模式，关闭输出，电源异常条件移除后可自动恢复

Protected mode, turn off the output power to remove the abnormal conditions can be automatically restored

环境ENVIRONMENTAL

工作温度 WORKING TEMP

 -20-60℃（请参考负载减额曲线）

工作湿度WORKING HUMIDITY

20-90%.无结冰No icing

储存温度.湿度 STORAGE TEMP, HUMIDITY

-40-85℃.10-95%

温度系数TEMP COEFFICIENT

±0.03%/℃（0-45℃）

耐振动 VIBRATION

10-500HZ.2G 10分钟/周期.X.Y.Z轴各60分钟

安规和电磁兼容

SAFETY&EMC

安全规范 SAFETY STANDARDS

IEC 60950-1安全标准符合GB4943

耐压 WITHSTAND VOLTAGE

I/P-O/P:1500VAV I/P-FG:1000VAC O/P-FG:500VAC

绝缘阻抗 ISOLATION RESISTANCE

I/P-O/P. I/P-FG. O/P-FG  50M/500VAC

电磁干扰EMC IMMUNITY

符合EN55015：2006+A1：2007+A2:2009

谐波电流HARMONIC CURRENT

符合EN61000-3-2：2006+A1：2009+A2：2009

电磁耐受EMC TOLERANCE

符合EN61000-4-8

其它NOTE

尺寸 SIZE:L199 x W98 x H38(mm)

包装PACKING：540±30g/PCS 20PCS/箱 BOX

备注REMARKS

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25℃of ambient temperature.

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.

3. Tolerance : includes set up tolerance, line regulation and load regulation.

4.Measuring method of linear adjustment rate: under the rated load, from low to high voltage test.

5.Test method: load adjustment rate from 0 to 100% of rated load

6.Power supply should be considered as part of the system components. Requires a combination of terminal equipment related to electromagnetic compatibility confirmed